IMPORTANT - PLEASE READ AND FOLLOW✓ Before beginning, please read these instructions completely and carefully.✓ Do not remove permanently affixed la
10Fig. 1.4FITTING THE ADJUSTABLE FEETThe adjustable feet must be fitted to the base of the cooker before use.Rest the rear of the cooker on a piece o
11ABABAABBFig. 1.8Fig. 1.9ASSEMBLING THE BACKGUARD OR THE ISLAND TRIMIt is mandatory to install the backguard or the island trim• Assemble the backg
12ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS1. The anti-tip bracket has to be attached as shown on figure below, it has to be fixed on the re
13Gas supply lineShutoff valve“open” positionTo rangeFig. 2.1All gas connections must be made according to national and local codes. This gas supply (
14PRESSURE REGULATOR INSTALLATIONLOCKArrowSTEP 2Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gask
15AASTEP 3Insert the extension pipe + pressure regulator group in the “A” bracket.STEP 4Assemble the extension pipe + pressure regulator group to the
16BBSTEP 5Fix the “B” bracket on the back of the range by the 2 (two) screws supplied with the kit for gas connection.The regulator cover must be ordi
17ConnectorPressureregulator1/2” G cylindrical(ISO 228-1) female1/2” NPT(conical)male1/2” NPTfemale1/2” NPTfemale1/2” G cylindrical(ISO 228-1) maleExt
18Fig. 2.4TEST POINT ADAPTERThe Test Point adapter is available from the After-Sales Service.c) Any conversion required must be performed by your dea
1912NATURAL GASREGULATIONLP/PROPANEREGULATIONAcomponentFig. 2.5REGULATORCOVERPressure regulatorCONVERSION TO LP/PROPANE GASEvery range is provided wit
2✓ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.✓ WHAT TO DO IF YOU SMELL GAS:• D
20OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS✓ Remove the gratings and the burner covers;✓ Using a wrench substitute the nozzle inject
21SETTING THE BURNER MINIMUMWhen switching from one type of gas to another, the minimum flow rate must also be correct: the flame should not go out e
22Fig. 2.9Fig. 2.10Fig. 2.11Fig. 2.12OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTORS OF THE OVEN AND BROIL BURNERS(LEFT and RIGHT OVEN
23ADJUSTMENT OF THE OVEN BURNER MINIMUM(LEFT and RIGHT OVEN)This needs to be done only for the oven burner (the broil is a fixed capacity) by acting o
24If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.Check
25WIRING DIAGRAM
Cod. 1104646 - ß1The manufacturer cannot be held re spon sible for possible inaccuracies due to printing or transcription errors in the present bookle
3DATA PLATECONVERSION LABELThis appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any
4WARNING!THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.Improper installation, adjustment, alteration, services, or maintenance can cause
5GENERAL INFORMATION1. Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-Lat
6installationPROXIMITY TO SIDE CABINETS1. This range may be installed directly adjacent to existing 36" (914 mm) high base cabinets. Range dime
7ABDCGAS AND ELECTRIC CONNECTIONDotted line showing the positionof the range when installed* : Depending on feet regulationArea for ELECTRICAL connect
8(457 mm)18" min.30" min.(762 mm)(914 mm)36"0"(0 mm)0"(0 mm)20" min. (500 mm)11" 13/16 min. (300 mm)13" max. (
9Fig. 1.3cPROXIMITY TO SIDE CABINETSRANGE WITH ISLAND TRIM(457 mm)18" min.30" min.(762 mm)(914 mm)36"0"0"(0 mm)(0 mm)20"
Commentaires sur ces manuels