IMPORTANT - PLEASE READ AND FOLLOW✓ Before beginning, please read these instructions completely and carefully.✓ Do not remove permanently affixed labe
10햲Fig. 1.4FITTING THE ADJUSTABLE FEETThe adjustable feet must be fitted to the base of the cooker before use.Rest the rear of the cooker on a piece o
11햲ABABAABBFig. 1.8Fig. 1.9ASSEMBLING THE BACKGUARDOR THE ISLAND TRIMIt is mandatory to install thebackguard or the island trim• Assemble the backgua
12ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS1. The anti-tip bracket has to be attached as shown on figure below, it has to be fixedon the rea
13Gas supply lineShutoff valve“open” positionTo rangeFig. 2.1All gas connections must be made according to national and local codes. This gassu
14햳PRESSURE REGULATOR INSTALLATIONLOCKArrowSTEP 2Assemble the 1/2” NPT connector + pressure regulator group to theextension pipe interposi
15햳AASTEP 3Insert the extension pipe + pressure regulatorgroup in the “A” bracket.STEP 4Assemble the extension pipe + pressureregulator group
16BBSTEP 5Fix the “B” bracket on the back of the range by the 2 (two) screwssupplied with the kit for gas connection.The regulator cover must be
17ConnectorPressureregulator1/2” G cylindrical(ISO 228-1) female1/2” NPT(conical)male1/2” NPTfemale1/2” NPTfemale1/2” G cylindrical(ISO 228-1) m
18햳Fig. 2.4TEST POINT ADAPTERThe Test Point adapter is available fromthe After-Sales Service.c) Any conversion required must be performed by your dea
1912NATURAL GASREGULATIONLP/PROPANEREGULATIONAcomponentFig. 2.5REGULATORCOVERPressure regulatorCONVERSION TO LP/PROPANE GASEvery range is provided
2✓ Do not store or use gasoline or other flammable vapors and liquidsin the vicinity of this or any other appliance.✓ WHAT TO DO IF YOU SMELL GAS:• Do
20햳OPERATIONS TO BE PER-FORMED WHEN SUBSTI-TUTING THE INJECTORS✓ Remove the gratings and the burnercovers;✓ Using a wrench substitute the nozzleinject
21SETTING THE BURNER MINIMUMWhen switching from one type of gas to another, the minimum flow rate must also becorrect: the flame should not go out ev
22햳OPERATIONS TO BE EXECUTED FOR THEREPLACEMENT OF THE INJECTORS OF THEOVEN AND BROIL BURNERSa) Oven Burner– Lift and remove the lower panel inside th
23ADJUSTMENT OF THE OVEN BURNER MINIMUMThis needs to be done only for the oven burner (the broil is a fixed capacity) by actingon the thermostat in th
24If codes permit and a separate ground wire is used, it is recommended that aqualified electrician determine that the ground path is adequate.Che
25햴WIRING DIAGRAM
Cod. 1103631 - ß1The manufacturer cannot be held re spon sible for possible inaccuracies due to printing or transcription errors inthe present booklet
3DATA PLATECONVERSION LABELThis appliance is designed and manufactured solely for the cooking of domestic (household)food and in not suitable for any
4WARNING!THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.Improper installation, adjustment, alteration, services, or maintenance can
5GENERAL INFORMATION1. Installation must conform with local codes or, in theabsence of local codes, with the National Fuel Gas Code,ANSI Z223
6installation쐃PROXIMITY TO SIDE CABINETS1. This range may be installed directly adjacent to existing 36"(914 mm) high base cabinets. Range dimen
7CDBAGAS AND ELECTRIC CONNECTIONDotted line showing the positionof the range when installed* : Depending on feet regulationArea for GAS connectionArea
(457 mm)18" min.30" min.(762 mm)(914 mm)36"0"(0 mm)0"(0 mm)20" min. (500 mm)11" 13/16 min. (300 mm)13" max. (3
9햲Fig. 1.3cFig. 1.3dPROXIMITY TO SIDECABINETSRANGE WITH ISLAND TRIM(457 mm)18" min.30" min.(762 mm)(914 mm)36"0"0"(0 mm)(0 mm
Commentaires sur ces manuels